 |
   |
产品详情
PRODUCT DEscriptION:
XYLAN 1014/P01931E DEEP MED. BLUE #524
PRODUCT CODE: P01931E
GENERAL INFORMATION:
The primary end use for this coating is: DRY FILM LUBRICATING COATING
PRODUCT SPECIFICATIONS:
SOLIDS, theoretical: 30.00 ± 2.0% by wt., 19.88 ± 2.0% by vol.
DENSITY, theoretical: 9.00 ± 0.2 lb/gal, 1.08 ± 0.02 Kg/liter
COVERAGE, theoretical: 318.87 sq.ft./gal.@ 1 mil, 7.24 sq.m./Kg.@ 25 microns
VISCOSITY, as shipped: 25 - 35 SECONDS ZAHN #3 (S90) CUP at 77°F (25°C)
TYPICAL PROPERTIES:
FLASH POINT: 85°F, 29°C
VOLATILE ORGANIC CMPDS: 6.42 lb./gal., 770.40 grams/liter
PREPARATION OF PARTS FOR COATING:
Parts must be free of dirt, oil and other soils to achieve good adhesion and defect free coatings. The
following are the recommended substrates and substrate preparations used with this coating:
SUBSTRATES: MOST metaLS, SOME CERAMICS AND PLASTICS
PREPARATION: DEGREASE; LIGHT GRITBLAST RECOMMENDED; ZINC PHOSPHATE ON
STEEL RECOMMENDED; MAY BE USED OVER ETCHED ZINC PLATE.
PRIMERS: MAY BE USED OVER XYLAR 1, 2 OR XYLAN 4090 SERIES PRIMERS.
PREPARATION OF COATING MATERIAL:
Mix containers thoroughly by shaking or stirring until any solid material on the bottom has been
eliminated. Best results are obtained when the coating temperature is 65-90°F (18-32°C). Adjust
viscosity, if necessary, using the recommended thinner and an accurate Zahn Viscosity Cup. Other
viscosity cups may also be used. Add thinner in increments of 2% until proper viscosity is achieved.
Low viscosity produces runs and sags and low film thickness. High viscosity produces poor
sprayability and uneven appearance. Any dried coating or dirt may be removed by passing the
coating through a 100-200 micron filter.
APPLICATION VISCOSITY: 25 - 40 SECONDS ZAHN #2 (S90) CUP AT 77°F (25°C)
VISCOSITY ADJUSTMENT: NMP/XYLENE - 2:1 OR SOLVENT 99B, AS NEEDED.
OTHER INFORMATION: AVOID CREATING FOAM WHILE MIXING.
_________________________________________________________________________________
NON-WARRANTY. The information presented in this publication is based upon the research and experience of Whitford and is to the best of
its knowledge accurate; however, no guarantee of its accuracy is made, Since Whitford has no control over the conditions under which its
products may be employed; and since information as to the physiological and other properties of its products is incomplete, Whitford cannot
guarantee the results obtained and assumes no liability whatsoever for possible damage or injury whether or not caused by following the
suggestions in this brochure. Whitford will not be liable for resulting or consequential damage. Whitford warrants that none of its commercial
products infringes the claims of any United States patent but no license is granted nor recommendation made hereby to practice any
invention covered by any patent owned by Whitford or by others.
您可能想要查看
更多推荐产品
阻燃级PBT台湾新光E202G30
23.00
德国巴斯夫PA66 A3EG6
28.00
透明PC美国GE 241R
20.00
免责声明：以上所展示的信息由会员自行提供，内容的真实性、准确性和合法性由发布会员负责。塑料网对此不承担任何责任。
友情提示：为规避购买风险，建议您在购买相关产品前务必确认供应商资质及产品质量。
